List of Figures

| Table of Contents | List of Figures | List of Tables |

Figure 1. Sources of Additional Information about Origin200

Figure 1-1. Two-module Origin200 System, Front View

Figure 1-2. Two-module Origin200 System, Rear View

Figure 1-3. Two-module Origin200 Server in a Rack

Figure 1-4. Logic Carrier Assembly

Figure 1-5. The Origin200 Main System Board and CPU Daughter Card

Figure 1-6. PCI Backplane and Slot IDs

Figure 1-7. Layout of DIMM Sockets on the Origin200 Main System Board

Figure 1-8. Origin200 5.25-inch Peripheral Carrier and Drive Bay

Figure 1-9. Origin200 3.5-inch Drive, Sled, and Bay

Figure 1-10. Air Flow Through Origin200

Figure 2-1. Minimum Clearances for the Origin200 Server, Tower Configuration

Figure 2-2. Basic Items Included With the Origin200 Server, Tower Configuration

Figure 2-3. Basic Items Included With the Origin200 Server, Rack-Mountable Configuration

Figure 2-4. Origin200 Connectors

Figure 2-5. SCSI Drive ID Numbering for 3.5-Inch Drives

Figure 2-6. Installing 3.5-Inch Drives in Origin200

Figure 2-7. Removing the 5.25-Inch Peripheral Carrier

Figure 2-8. Removing a Blanking Plate and the Rear Access Plate from the Peripheral Carrier

Figure 2-9. Inserting a 5.25-Inch Drive in the Peripheral Carrier

Figure 2-10. Attaching a Power Connector to a 5.25-inch Drive

Figure 2-11. Attaching the SCSI Cable to a 5.25-Inch Drive

Figure 2-12. Replacing the Rear Access Plate on the Peripheral Carrier

Figure 2-13. Replacing the 5.25-Inch Peripheral Carrier

Figure 2-14. Attaching an Ethernet Networking Cable to An Origin200 module

Figure 2-15. Attaching the Serial Cable

Figure 2-16. Removing the Side Panel of the Second (Slave) Module

Figure 2-17. Removing the Module System Controller (MSC) Access Plate

Figure 2-18. MSC DIP Switch Location and Settings

Figure 2-19. Attaching the Grounding Cable

Figure 2-20. Attaching the CrayLink Interconnect Cable and Grounding Cable

Figure 2-21. Turning On the Master Power Switch

Figure 2-22. Turning On the Front Power Switch

Figure 3-1. Placing the Origin200 on a Work Surface

Figure 3-2. Origin200 Rack Mounting Ears

Figure 3-3. Attaching the Rack Mounting Hardware (Ears)

Figure 3-4. Lifting the Origin200 Server Into a Rack

Figure 3-5. Attaching the Plastic End Caps to a Rackmounted Server

Figure 4-1. The Origin200 Front Panel

Figure 4-2. Turning On the Master Power Switch

Figure 4-3. Turning On the Front Power Switch

Figure 4-4. Turning Off the Front Power Switch

Figure 4-5. Turning Off the Master Power Switch

Figure 4-6. Attaching a Serial Cable To Port 1 of the Origin200 Server

Figure 4-7. Location of the AUX Port

Figure 4-8. Example /hw Filesystem

Figure 4-9. Removing the System Cover, Tower Origin200 System

Figure 4-10. Opening the Chassis Access Door, Tower Origin200

Figure 4-11. Locking the Chassis With the Locking Tabs

Figure 4-12. Adjusting the Feet

Figure 5-1. Attaching A Grounding Wrist Strap

Figure 5-2. Locating DIMMs In the Origin200 Server

Figure 5-3. How DIMM Pairs Are Grouped In the Origin200 Server

Figure 5-4. Installing a DIMM

Figure 5-5. Attaching A Grounding Wrist Strap

Figure 5-6. Locating DIMMs In the Origin200

Figure 5-7. How DIMM Pairs Are Grouped In Origin200

Figure 5-8. Removing DIMMs

Figure 6-1. Attaching A Grounding Wrist Strap

Figure 6-2. Locating the PCI Option Slots

Figure 6-3. Removing a PCI Slot Blanking Plate

Figure 6-4. Inserting a PCI Option Board

Figure 6-5. Attaching A Grounding Wrist Strap

Figure 6-6. Removing a PCI Option Board Screw and Board

Figure 6-7. Replacing a PCI Option Blanking Plate and Screw

Figure 7-1. Location of the 5.25-Inch Drive Bay

Figure 7-2. 5.25-Inch Peripheral Carrier

Figure 7-3. Removing the 5.25-Inch Peripheral Carrier

Figure 7-4. Removing a Blanking Plate and the Rear Access Plate from the Peripheral Carrier

Figure 7-5. Installing a 5.25-Inch Drive in the Peripheral Carrier

Figure 7-6. Replacing the 5.25-Inch Peripheral Carrier

Figure 7-7. Removing the Peripheral Carrier

Figure 7-8. Removing the Rear Access Plate from the Peripheral Carrier

Figure 7-9. Removing A Drive From the Peripheral Carrier

Figure 7-10. Replacing the Front Blanking Plate and Rear Access Plate

Figure 7-11. Replacing the 5.25-Inch Peripheral Carrier

Figure 7-12. The 3.5-Inch Drive Bay and Correspondence of SCSI IDs to Drive Sots

Figure 7-13. Example 3.5-Inch Drive Slot Blanking Plate

Figure 7-14. Opening the Front Door of Origin200

Figure 7-15. How the 3.5-inch Drives are Numbered in Origin200

Figure 7-16. Installing a 3.5-inch Peripheral in Origin200

Figure 7-17. Opening the Front Door of Origin200

Figure 7-18. How the 3.5-inch Drives are Numbered in Origin200

Figure 7-19. Removing a 3.5-inch Drive from Origin200

Figure 7-20. Location of the Serial Port Connectors on Origin200

Figure 8-1. Ethernet 10-Base-T/100-Base-TX Port LEDs

Figure 8-2. Location of the Power Supply Test Button and LED

Figure 9-1. Removing the Chassis Access Cover

Figure 9-2. Cable Connections and Spring Clips On the SCSI Backplane

Figure 9-3. Disconnecting the Fan and Fan Power Cable (Other Components Removed For Clarity)

Figure 9-4. Removing the Fan From the System

Figure 9-5. Removing the Front Bezel Crossbar

Figure 9-6. Removing the System Controller Assembly From the Chassis

Figure 9-7. Removing the Module System Controller Board From the Carrier

Figure A-1. Origin200 Serial Port Pinout Assignments

Figure A-2. Origin200 Parallel Port Pinout Assignments

Figure A-3. Origin200 Ethernet 10-Base-T/100-Base-TX Port Pinout Assignments

Figure A-4. Origin200 AUX Port Pinout Assignments