List of Figures

| Table of Contents | List of Figures | List of Tables |

Figure 1-1. Checking the OCTANE Channel Option Shipment

Figure 1-2. Powering Off the OCTANE Workstation

Figure 1-3. Removing the Monitor Cable

Figure 1-4. Attaching the Wrist Strap

Figure 1-5. Identifying the Compression Connector

Figure 1-6. Removing the XIO Module Screws

Figure 1-7. Removing the XIO Module

Figure 1-8. Supporting the XIO Module

Figure 1-9. Placing the XIO Module on Its Side

Figure 1-10. Placing a Protective Cap on the XIO Compression Connector

Figure 1-11. Removing the Baffle

Figure 1-12. Removing the Baffle

Figure 1-13. Attaching the OCTANE Channel Option Board to the XIO Module

Figure 1-14. Attaching the Flex Cables From the OCTANE Channel Option Board to the Graphics Board

Figure 1-15. Attaching the Flex Cables to the Graphics Board

Figure 1-16. Attaching the Flex Cable Guard

Figure 1-17. Removing the Screw From the Graphics Board

Figure 1-18. Sliding the Cable Guard Under the I/O Panels

Figure 1-19. Sliding the Cable Guard Behind the Standoff

Figure 1-20. Attaching the Screw to Anchor the Cable Guard to the Graphics Board

Figure 1-21. Installing Slots A and D Toward the Interior of the OCTANE Workstation

Figure 1-22. Replacing the XIO Module

Figure 1-23. Replacing the XIO Module Screws

Figure 1-24. Replacing the Monitor Cable

Figure 1-25. Powering On the OCTANE Workstation

Figure 1-26. Rear View of the OCTANE Workstation

Figure 2-1. Attaching the Breakout Box Cable Connector to the OCO Board I/O Connector

Figure 2-2. Connecting the Breakout Box to Four Monitors

Figure 2-3. Connecting the Four Monitors to the Breakout Box

Figure 2-4. Moving the Cursor Between Monitors

Figure 2-5. Arranging Four Monitors in a Side-by-Side Configuration

Figure 2-6. Moving the Cursor Between Four Side-by-Side Monitors

Figure 2-7. Connecting the Two Stacked Monitors to the Breakout Box

Figure 2-8. Moving the Cursor Between Two Stacked Monitors

Figure 2-9. Arranging Two Monitors in a Side-by-Side Configuration

Figure 2-10. Moving the Cursor Between Two Side-by-Side Monitors

Figure 2-11. Identifying the Section for the Head-Mounted Display

Figure 2-12. Identifying the Section for the Minify or Single Monitor Mode

Figure 3-1. OCTANE Channel Option Board and Graphics Subsystem

Figure 3-2. Display Surface for 4@640x486_30i Output Format

Figure 3-3. Display Surface for 4@640x480_60 Output Format

Figure 3-4. Display Surface for 4@800x600_60 Output Format

Figure 3-5. Display Surface for 2@640x480_60q Output Format

Figure 3-6. Display Surface for 1@640x480_60 Output Format

Figure 3-7. Display Surface for 2@800x486_30qi Output Format

Figure 3-8. Display Surface for 2@800x600_60 Output Format

Figure 3-9. Display Surface for 2@880x808_30qi Output Format

Figure 3-10. Display Surface for 2@1024x946_30qi Output Format

Figure 3-11. Display Surface for 2@1160x960_30qi Output Format

Figure 4-1. Orienting the XIO Module and Graphics Board

Figure 4-2. Removing the Cable Guard

Figure 4-3. Sliding the Cable Guard Beneath the I/O Panels

Figure 4-4. Sliding the Cable Guard From Beneath the I/O Panels

Figure 4-5. Replacing the Screw Holding the Graphics Board to the XIO Module

Figure 4-6. Releasing the Flex Cables From the Graphics Board

Figure 4-7. Removing the Flex Cables

Figure 4-8. Removing the OCTANE Channel Option Board

Figure 4-9. Placing a Blank Panel in Slot B

Figure 4-10. Placing the Baffle Over Two Blank Panels

Figure A-1. OCTANE Channel Option Board

Figure A-2. OCTANE/SI Graphics Board

Figure A-3. OCTANE/SI With Texture Memory Option Board

Figure A-4. OCTANE/SSI Graphics Board

Figure A-5. OCTANE/MXI Graphics Board