List of Figures

| Table of Contents | List of Figures | List of Tables |

Figure 1-1. Front View of the Workstation
Figure 1-2. Rear View of the Workstation
Figure 1-3. Connecting the K eyboard and Mouse Cables
Figure 1-4. Connecting the Ethernet Cable
Figure 1-5. Connecting the Monitor Cable
Figure 1-6. Connecting the Power Cable
Figure 1-7. Cabling a Dual-enclosure Workstation
Figure 1-8. Powering On the W orkstation
Figure 1-9. Login Screen
Figure 1-10. Peripheral Icons
Figure 1-11. Toolchest Menu
Figure 1-12. Console Window
Figure 1-13. System Shutdown Notifier
Figure 1-14. Power Button and Reset Button
Figure 1-15. Shutdown Caution Message
Figure 1-16. Shutdown System Window
Figure 1-17. System Shutdown Notifier
Figure 1-18. Restart Notifier
Figure 1-19. System Shutdown Notifier
Figure 1-20. Power Off/Restart Notifier
Figure 1-21. Restart Notifier
Figure 2-1. Single- and Dual-enclosure Rackmount Workstations
Figure 2-2. Front Panel Components
Figure 2-3. Rear Panel Components
Figure 2-4. System Architecture
Figure 2-5. DIMM Sockets and Pairs
Figure 2-6. Internal Hard Disk Drives and DVD-ROM Drive
Figure 2-7. Power Supply Location
Figure 3-1. Removing the Enclosure Cover
Figure 3-2. Installing the Enclosure Cover
Figure 3-3. PCI and PCI–X Card Slots Located in the Rear Panel
Figure 3-4. Removing the Lower PCI/PCI–X Support Bracket
Figure 3-5. Removing a Blanking Plate
Figure 3-6. Installing the Card and Retaining Screw
Figure 3-7. Replacing the Lower PCI/PCI–X Support Bracket
Figure 3-8. Removing the Lower PCI/PCI–X Support Bracket
Figure 3-9. Removing the Retaining Screw and Extracting the Card
Figure 3-10. Installing a Blanking Plate
Figure 3-11. Replacing the Lower PCI/PCI–X Support Bracket
Figure 3-12. Disk Drive Location
Figure 3-13. Installing a Disk Drive
Figure 3-14. Removing a Disk Drive
Figure 3-15. Layout of DIMM Slots and Local Memory Banks
Figure 3-16. Opening the Enclosure Cover to Install DIMMs
Figure 3-17. Removing the Plastic Air Baffle
Figure 3-18. Inserting a DIMM
Figure 3-19. Opening the Enclosure Cover to Remove DIMMs
Figure 3-20. Removing the Plastic Air Baffle
Figure 3-21. Removing a DIMM
Figure 3-22. L1 Controller Display on the Front Panel
Figure 3-23. Opening the Enclosure Cover to Access the L1 Controller Display
Figure 3-24. Removing the L1 Controller Display Panel
Figure 3-25. Installing an L1 Controller Display Panel
Figure 3-26. Power Supply Location
Figure 3-27. Removing the Power Supply
Figure 3-28. Installing the Power Supply
Figure 4-1. Full Support Sequence
Figure A-1. Rear Panel Connectors
Figure A-2. Ethernet 10/100/1000BaseT Port Pinout
Figure A-3. PS/2 Keyboard and Mouse Port Pinout
Figure A-4. Serial Port Pinouts and Locations
Figure A-5. External SCSI Port Pin Number Locations
Figure A-6. Stereo Jack Connector Conductors
Figure A-7. USB Type A Connector Pin Number Locations
Figure A-8. DVI-I Port Pinout and Location
Figure A-9. Stereo View Port Pinout
Figure A-10. Genlock Port Pinout
Figure A-11. Swap Ready Port Pinout
Figure B-1. Separating the Chassis Rail from the Slide Rail
Figure B-2. Attaching the Rear Mounting Bracket to the Slide Rail
Figure B-3. Attaching Chassis Rails to the Module Chassis
Figure B-4. Mounting Hole Pattern of Rack Vertical Rails
Figure B-5. Placing the Bar Nuts on the Rack Rails
Figure B-6. Attaching the Slide Rail to the Rack
Figure B-7. Installing Clip Nuts in Rack Rails
Figure B-8. Pressing the Safety Latches
Figure B-9. Securing the Module to the Rack
Figure B-10. Releasing the Safety Latches
Figure B-11. Releasing the Slide Latches
Figure D-1. Connecting a Monitor to the Workstation Expansion Enclosure
Figure D-2. USB Keyboard and Mouse Connected Directly to the Tezro Enclosure
Figure D-3. Second Keyboard and Mouse Connected via Optional USB Extender